Offers high performance scanning at a moderate. Backroom to make your scanner from Motorola Symbol LS scanner. Symbol scanners are built to last and easy to use while Symbol handhelds are built with an ergonomic and rugged design.
The affordable Symbol LS handheld barcode scanner provides fast, reliable scanning in an ergonomic, lightweight form. A carriage return enter after your buying decision easier than ever.
The wide working range of its sales representative. Barcode Scanner High performance scanning at the one million mark. It all the retail stores, Healthcare, lightweight form. Manufacturing, lightweight zymbol fast and running. Hope this helps get the scanner up and running. Dell xps lx. Scan the barcode corresponding with the volume level you wish to achieve. Symbol scanners are lightweight and handheld scanners used in numerous different settings, including retail stores, warehouses and hospitals.
Many great value in shorter check-out lines and Stand. You will need to print this article with the barcodes below and scan them in the sequence indicated. C-2 Code C-2 Interleaved 2 of C-2 GS1 DataBar C-2 PDF C-3 Data Matrix C-3 Maxicode C-3 QR Code C-4 US Postnet C-4 UK Postal D-1 Cancel About This Guide xv. Service Information If you have a problem with your equipment, contact Motorola Enterprise Mobility support for your region.
Unpacking Remove the digital scanner from its packing and inspect it for damage. Getting Started 1 - 3. Figure Connecting the Interface Cable 3. Figure Securing the Clamp 5. Removing the Interface Cable 1. Connecting Power if required If the host does not provide power to the digital scanner, connect an external power supply to the digital scanner: 1. Configuring the Digital Scanner To configure the digital scanner, use the bar codes in this manual, or the Scan configuration program.
Chapter 2 Scanning Introduction This chapter provides beeper and LED definitions, techniques involved in scanning bar codes, general instructions and tips about scanning, and decode zone diagrams. Beeper Definitions The digital scanner issues different beep sequences and patterns to indicate status. The data is ignored. This occurs if the digital scanner is not properly configured. Check option setting. Enter value using numeric bar codes. Scan Set Default Parameter beep sequence on page A bar code not in the current MPDF sequence was scanned.
There is not enough buffer space to store the current MPDF symbol. Duration of tones are short. Add leading zeros to the front if necessary. Rule entry mode exited. Low beep Delete last saved rule. The current rule is left intact. Duration of tones are very long. Erase some existing rules, then try to save rule again.
It is not necessary to re-enter the current rule. Rule entry mode exited because of an error or the user asked to exit rule entry. Re-enter criterion or action. All previously entered criteria and actions are retained. Criteria or action list is too long for a rule. Wait several seconds and scan again. This is normal and usually happens when the PC cold boots. Green A bar code was successfully decoded.
Red A data transmission error or digital scanner malfunction occurred. Scanning with the Digital Scanner 1. Figure Scanning in Hand-Held Mode 4. Aiming Hold the digital scanner between two and nine inches depending on symbol density; see Decode Zones on page from the symbol, centering the aiming pattern cross hairs on the symbol.
Scanning in Presentation Mode The optional Intellistand adds greater flexibility to scanning operation. If the configuration requires a power when pressing the trigger. Incorrect host interface cable is Connect the correct host interface used. Re-connect cables. Digital scanner is disabled. For Synapse or IBM x mode, enable the digital scanner via the host interface. Otherwise, see the technical person in charge of scanning. CTS is not asserted.
Aiming pattern is disabled. Enable the aiming pattern. See Decode Aiming Pattern on page Digital scanner emits aiming pattern, Digital scanner is not programmed Program the digital scanner to read but does not decode the bar code.
See Chapter 10, Symbologies. Bar code symbol is unreadable. Scan test symbols of the same bar code type to determine if the bar code is defaced. The symbol is not completely Move the symbol completely within the inside aiming pattern. Digital scanner emits 4 short high Digital scanner has not completed Wait several seconds and scan again.
USB initialization. Table Troubleshooting Continued Problem Possible Causes Possible Solutions Digital scanner decodes bar code, Digital scanner is not programmed Scan the appropriate host type but does not transmit the data to the for the correct host type. See the host. Interface cable is loose. Re-connect the cable.
If 4 long low beeps are heard, a Set the digital scanner's transmission error occurred. If 5 low beeps are heard, a Configure the digital scanner's conversion or format error conversion parameters properly. Host displays scanned data Digital scanner is not programmed Scan the appropriate host type incorrectly.
For RS, set the digital scanner's communication parameters to match the host's settings. Program the proper editing options e. Digital scanner emits RS receive error.
Normal during host reset. Normal when scanning the Code 39 beeps. Buffering Clear Buffer bar code or upon attempt to transmit an empty Code 39 buffer. RS mode. Chapter 4 User Preferences Introduction You can program the digital scanner to perform various functions, or activate different features.
Scanning Sequence Examples In most cases, scanning one bar code sets the parameter value. Errors While Scanning Unless otherwise specified, to correct an error during a scanning sequence, just re-scan the correct parameter. User Preferences Parameter Defaults Table lists defaults for user preferences parameters.
You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. View and download manuals available only for.
Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual. Buy as much as you need. Chapter 3: Maintenance and Technical Specifications. A bar code symbol was decoded if decode beeper is enabled. A transmission error occurred when scanning a symbol. The data is. Correct entry scanned or correct menu sequence performed. Keyboard parameter selected. Successful program exit with change in parameter setting.
The Code 39 buffer was erased or there was an attempt to clear or. File ID error. A bar code not in the current MPDF sequence was. Out of memory. There is not enough buffer space to store the current. Bad symbology. Enter another digit. All criteria or actions cleared for current rule, continue entering rule.
Delete last saved rule. Out of rule memory. Erase some existing rules, then try to save rule. Cancel rule entry. Rule entry mode exited because of an error or the. Zebra Certified Printer Supplies labels, media. Printer Supply Selector Tool. Printer Parts. About Zebra OneCare Services. Declaration of Conformity. RoHS Declarations. Zebra Open Source Usage. LifeGuard for Android Updates. Security Alerts. Product Recalls.
VisibilityIQ Foresight Support. Developer Portal. Zebra TechDocs. Only supported when using Internet Explorer. Learn More. Search for previously released Certified or Beta drivers. For more information about how to access your purchased licenses visit the vGPU Software Downloads page.
0コメント